Skip to content
Root & Fifth

Guide

How to restring a bass: change your bass strings step by step

Remove the old set, thread each new string through the bridge, cut it to length, wind it neatly down the post and tune up, with the tools for each step.

Published

White bass body with four strings running into a chrome bridge with four adjustable saddles
Photo: jonathansautter / Pixabay

Knowing how to restring a bass saves money and keeps the instrument sounding its best. This guide covers a full change on an electric bass with a standard bridge: removing the old strings, fitting each new one, cutting it to length, winding it on and tuning up. Yamaha describes restringing an electric bass as simple and easy, a job that takes just minutes.

The steps are the same on a four-string and a five-string bass. Through-body bridges and string retainers on the headstock get their own notes below.

What you'll need

Essentials

  • A new set of strings

    : matched to your bass's scale length, bridge type and number of strings.
  • Wire cutters

    : trim each new string to length before winding it on.
  • Tuner

    : a clip-on or pedal tuner to bring the new strings up to pitch and check them as they stretch.
  • Towel or soft mat

    : lay the bass on it so the body and headstock do not get scratched.

Optional

  • String winder

    : turns the tuning keys faster when unwinding the old set.
  • Soft cloth

    : wipe the fingerboard and hardware while the strings are off.

Before you start: check the new set

Make sure the strings fit before you take anything off. A set has to match three things:

  • Scale length. Many basses are long scale (usually 34 inches), but short, medium and extra-long basses need their own sets. Rotosound's advice is to measure from where the ball end anchors to the nut and to the tuning post, and pick the string length that falls between the two.
  • Bridge. On a through-body bridge the strings enter from the back of the body, which uses up extra length. La Bella, for example, says its standard 760FS flatwound set is not suitable for through-body bridges and sells a separate version for them.
  • Number of strings. A five-string set adds a low B string; a six-string set adds a high C as well.

Lay a towel down and put the bass on it, face up, with the neck to your left if you are right-handed (to the right if you are left-handed), as Bass Guitar For Dummies suggests. A neck rest or a folded cloth under the neck keeps it steady.

Step 1: Loosen and remove the old strings

Turn each tuning key to slacken the string until it is completely loose; a string winder speeds this up. Then unwind the end from the post and pull the string out through the bridge.

One at a time or all at once

Either way works on a solid-body electric bass; Bass Guitar For Dummies changes them one at a time. Removing all the strings gives you a clear fingerboard and pickups to clean. Changing one at a time keeps most of the tension on the neck, so the bass comes back to pitch faster and the neck has less to settle. If your bass has a floating or unusual bridge, check its manual first.

While the strings are off, wipe the fingerboard, frets and pickups with a soft dry cloth.

Step 2: Thread the new string through the bridge

Start with the thickest string. One end has a ball; the other is tapered and wrapped in colored silk.

Push the tapered end through the bridge hole for that string and pull it toward the neck until the ball rests against the bridge. On a through-body bass, feed the string in from the back of the body. Check that the string sits in its own groove on its saddle.

Black-and-white close-up of two bass tuning posts with strings wound around them, a tuning key blurred in the background
Photo: Garyross70 / Pixabay

Step 3: Measure and cut the string

Lay the string along the neck and over the nut to its tuning post. Bass Guitar For Dummies suggests leaving 4 to 5 inches beyond the tuning post, enough for several wraps.

Where to cut

Read the instructions on your string pack first; makers differ.

  • Bass Guitar For Dummies says to cut only in the silk-wrapped end and never through the thick metal part of the string, or it will unravel.
  • La Bella says only the silk portion of its strings should wrap around the tuning post, and for its nylon tapewound set, that only the silk should be cut, or the string will unravel.
  • Rotosound warns that winding the speaking part of the string (the wound section past the silk) more than half a turn around the post may cause it to break, and advises avoiding cutting flatwound strings where possible. If you must cut a flatwound, leave enough turns around the post to keep it stable.

If the string reaches the post well before the silk begins, the set is too long for your bass; if the silk ends before the nut, the set is too short. Either way, it is the wrong length.

Cut with wire cutters in one clean snip.

Step 4: Wind the string onto the post

  1. Push the cut end straight down into the hole in the center of the tuning post, then bend it sideways so it sits in the slot at the top.
  2. Hold the string near the post so it does not slip, and keep light pressure on the bridge end so the ball stays seated.
  3. Turn the tuning key to tighten the string, rather than wrapping it by hand, which can twist it.
  4. Guide each wrap so it goes down the post, below the previous one. Dummies notes this increases the bend of the string over the nut, which helps sustain.
  5. Stop when the string is tight enough to stay in place.

Headstocks with string retainers

Many basses have a small bar or round clip on the headstock that holds the thinner strings down. Dummies says to pass the two thinnest strings under the retainers before tightening.

Back of a four-in-line bass headstock with four open-gear tuning machines
Photo: Jan van der Wolf / Pexels

Step 5: Repeat for each string

Work from the thickest string to the thinnest: E, A, D, G on a four-string; B first on a five-string. Bring each one roughly up to pitch as you go so the tension on the neck builds evenly.

Step 6: Tune, stretch and tune again

New strings stretch, and the neck bends forward slightly under the added tension, so the bass will drift flat at first. Tune all the strings, play for a few minutes, and tune again. Expect to repeat this several times over the first day.

Some players speed this up by pulling each string gently away from the fingerboard a few times along its length and retuning. Do it gently; strings are not designed to be yanked.

Step 7: Check the setup

If you changed to a different gauge or type, the new strings may pull on the neck differently. Elixir notes that changing gauges may require adjusting the action and intonation. Check for new buzzes or a change in string height, and see our bass setup guide if anything has moved.

Common mistakes when you restring a bass

  • Wrong length. Buying a set that is too short or too long for the scale length or bridge. Measure first.
  • Cutting too short. Too few wraps and the string can slip on the post. Leave enough for several neat wraps.
  • Wraps going up the post. The string sits too shallow over the nut and can buzz or rattle in the slot.
  • Unwound section wrapped around the post. The speaking part of the string should not be bent around the post more than half a turn; the silk end belongs there.
  • Ball end not seated. If the ball is not pressed fully against the bridge, the string will keep going flat until it settles.
  • Forgetting to retune. New strings take a day or so to stop stretching.

How to change strings on a 5-string bass

The steps are identical; there is simply one more string. Start with the low B, which is the thickest and the one most likely to be too long or too short: check the pack's length against your bass, as some five-string basses have a longer scale than 34 inches. Rotosound's chart pairs its extra-long sets with scale lengths of 33.5 to 36 inches.

What to do next

Note the date you changed strings so you know how long a set lasts under your hands. If you are choosing your next set, our guide to bass strings explains windings, materials and gauges, and flatwound vs roundwound compares the two main types.

Questions

How often should you change bass strings?

When they sound dull, will not stay in tune or feel gritty. Many players change roundwounds every few months; flatwounds can last for years.

Should I change bass strings one at a time or all at once?

Both work on a solid-body electric bass. Taking them all off lets you clean the fingerboard; changing one at a time keeps most of the tension on the neck.

How much string should I leave past the tuning post?

Bass Guitar For Dummies suggests 4 to 5 inches beyond the post. The aim is a few neat wraps of the silk-wrapped end around the post; check your string maker's instructions.

Do I need to cut bass strings?

Usually, because sets are made to fit several scale lengths. Cut in the tapered, silk-wrapped part if you can; La Bella warns that cutting its nylon strings anywhere but the silk will make them unravel.

How do I change strings on a 5-string bass?

The same way as on a four-string, starting with the low B string. Make sure the set is long enough for your bass, as some five-strings have a longer scale.

Sources