Guide
Bass truss rod adjustment: direction, small turns and when to stop
Check the neck relief, find the adjustment nut, turn it a quarter at a time in the right direction, let the neck settle and recheck, and stop at the first sign of trouble.
Published
The bass truss rod is a metal rod, usually steel, inside the neck that counters the pull of the strings. Adjusting it changes the neck relief, the slight forward bow that gives the strings room to vibrate. A bass truss rod adjustment is the first step of any setup, and done carefully, in small turns, it is something most players can learn.
This guide shows how to check whether your neck needs adjusting, which way to turn, how much, and when to stop and take the bass to a technician. The figures and limits come from Yamaha's bass setup guide and Bass Guitar For Dummies; if your bass's maker publishes its own instructions, follow those first.
What you'll need
Essentials
-
Truss rod wrench or Allen key
: the exact size and type for your bass, often supplied with it; a loose fit can strip the nut. -
Tuner
: relief is only measured with the strings at pitch. -
Capo
: holds the string at the first fret while you check the gap.
Optional
-
Feeler gauges
: measure the relief gap precisely. -
Screwdriver
: removes a truss rod cover, or turns the rod on basses that use a screw-type adjuster.
Why a bass neck needs adjusting
String tension pulls the neck forward. The truss rod pushes back. When the balance changes, so does the relief:
- New strings of a different gauge or type. Heavier strings, or flatwounds with a higher tension, pull harder. Elixir notes that a change of gauge may require adjusting the action and intonation.
- A different tuning. Tuning down slackens the strings and the neck straightens; tuning up does the opposite.
- Seasons. Wood takes on and loses moisture. Bass Guitar For Dummies notes that adjustments are needed about four times a year as the seasons change.
What a bass truss rod adjustment can and cannot do
The truss rod controls one thing: how much the neck bows along its length. It is the right tool when the whole neck has too much or too little curve. It is the wrong tool for problems in a single place:
- Strings high everywhere, relief fine: the saddles need lowering, not the rod.
- Buzz on one or two frets only: often a high or worn fret, which a technician levels.
- Strings hard to press at the first fret: often the nut slots, also a technician's job.
- Neck twisted from side to side: a truss rod cannot correct a twist.
Knowing this before you start saves turning the rod in search of a fix it cannot give, which is how rods end up overtightened.
Step 1: Check the relief
Before touching the rod, measure what you have. Tune the bass to pitch, then use Yamaha's method:
- Fret the lowest string at the first fret, with a capo or a finger.
- Fret the same string where the neck joins the body.
- Look at the gap between the string and the top of the seventh fret.
Yamaha says roughly .015 inch (about 1/64 inch) of space or less is right. Bass Guitar For Dummies gives a rougher check: with the string held at the first and last frets, a gap around the seventh to twelfth frets about the thickness of a credit card.
Reading the result
| What you see | What it means | Turn the rod |
|---|---|---|
| String touches the seventh fret, buzz on the first few frets | Too little relief, neck too straight or bowed back | Counterclockwise (loosen) |
| Large gap, strings high in the middle of the neck | Too much relief | Clockwise (tighten) |
| Gap within your maker's figure | Relief is fine | Leave it |

Step 2: Find the adjustment nut
Bass Guitar For Dummies notes that the adjuster is at the headstock on some basses and at the other end of the neck on others, and that on some basses the neck has to come off the body to reach it. Yamaha's guide says the cover is usually just behind the nut or under the pickguard; at the headstock it is often a small plate held by screws.
P bass truss rod adjustment and other body-end adjusters
Precision-style and other bolt-on basses vary: some have the adjuster at the headstock, some at the body end of the neck. A body-end adjuster may be reachable through a cut-out in the pickguard or may need the neck loosened or removed. If reaching it means taking the neck off, consider leaving the job to a technician. If you do it yourself, slacken the strings fully first; Dummies warns that loosening the neck screws under string tension can break the neck off and strip the screw holes.
Use the right tool
The adjuster takes an Allen key, a socket wrench or, on some basses, a screwdriver. Use the one supplied with the bass or an exact match. Dummies warns that forcing the rod with a tool that does not fit can strip it, which is expensive to repair.
Step 3: Turn in small steps
- Detune the strings a little, as Yamaha's guide does, so the rod is not fighting full string tension.
- Fit the tool fully into the adjuster.
- Turn a quarter turn at most, and never force it. If the nut resists, stop and read "When to stop" below. Yamaha says clockwise tightens the rod and straightens the neck (less relief), and counterclockwise loosens it and adds bow (more relief). Look at the nut from where the tool goes in.
- Retune the bass to pitch.
- Check the relief again with the same method as in Step 1.
Bass truss rod adjustment direction
The direction is the part people most often get wrong:
- Clockwise = tighten = less relief, the neck straightens and the strings come closer to the frets in the middle of the neck.
- Counterclockwise = loosen = more relief, the neck bows forward a little and the strings move away from the frets.
Some basses use a two-way (dual-action) rod that can push the neck in either direction, and some makers describe the direction differently. If your manual gives other instructions, follow the manual.
Step 4: Wait and recheck
Wood does not respond instantly. Bass Guitar For Dummies advises turning the rod no more than a quarter to a half turn per day and letting the neck settle for a day before adjusting further. A practical routine:
- Make one small adjustment.
- Retune and check the relief.
- Leave the bass tuned to pitch overnight.
- Check again the next day before deciding whether to turn further.
Once the relief is right, move on to string height and intonation, in that order, as described in our bass setup guide. The truss rod sets relief only; the action itself is set at the saddles.
When to stop
Stop and take the bass to a qualified technician if any of these happen:
- Heavy resistance. Yamaha says that if you feel heavy resistance when turning clockwise, stop, back the rod off a quarter turn and take the bass to a qualified tech. An overtightened rod can cause stress cracks in the neck or snap the rod, which Yamaha calls a serious and expensive repair.
- The nut will not move, or turns without any change in relief.
- The tool slips or the nut looks rounded.
- The neck is twisted, with one side of the fingerboard bowed differently from the other.
- Relief will not come right after several days of small adjustments.
- You are unsure. Yamaha notes that a music retailer can refer you to a guitar technician or luthier.
Common mistakes
- Using the truss rod to fix action. If relief is right and the strings are still high, adjust the saddles.
- Large turns. A full turn at once can overshoot badly and stress the rod.
- Measuring with the strings slack. Always retune before checking.
- Checking too soon. Give the neck time; the reading can change over a day.
- Ignoring a stiff nut. Forcing it is how rods break.
What to check next
After any truss rod change, recheck string height and intonation, because both move when the relief changes. If the adjustment was needed because you changed sets, our guides to bass strings and how to restring a bass explain how gauge and winding change the pull on the neck.
Questions
Which way do you turn a bass truss rod?
On most basses, clockwise tightens the rod and reduces relief, straightening the neck; counterclockwise loosens it and adds relief. Some basses use a different type of rod, so check your manual.
How much should I turn a truss rod at once?
A quarter turn at most, then retune and check. Bass Guitar For Dummies advises no more than a quarter to a half turn per day, letting the neck settle in between.
Does the truss rod adjust the action?
Only indirectly. The truss rod sets neck relief; string height is adjusted at the bridge saddles. Adjust relief first, then set the action.
When should I not adjust the truss rod myself?
When the nut is stiff, does not move, or the right tool does not fit, and when the neck is cracked or twisted. Yamaha says to stop if you feel heavy resistance and take the bass to a qualified technician.
Sources
Read next
Guide
Bass guitar setup: neck relief, action, intonation and pickup height
Four adjustments, always in the same order: neck relief, string height, intonation and pickup height, with the checks for each and the signs that a job belongs to a technician.
Guide
How to restring a bass: change your bass strings step by step
Remove the old set, thread each new string through the bridge, cut it to length, wind it neatly down the post and tune up, with the tools for each step.
Buying guide
Bass strings: windings, materials, gauges and how to choose a set
What the winding, the metal, the gauge and the length of a string do to the sound and feel of a bass, and how to read a string pack before you buy.